Maytag Washer Stuck on Sensing (7 Quick Fixes)

Sometimes the Maytag washers are just stuck in the sensing mode. While the washer would sense the load but it will not start the washer. As a result, you end up facing the Maytag washer stuck on sensing error.

This is a pretty common issue with Maytag washers. But fortunately, fixing it isn’t as complicated as it might seem.

Below, you will find a few troubleshooting methods that will help you fix the Maytag washer stuck on sensing error.

So go ahead and check them out:

What Causes Maytag Washer To Stuck on Sensing?

This problem arises when the washer fails to move on to the next cycle and remains stuck in sensing mode. In most cases, this can be resolved by simply unplugging the washer, waiting a few seconds and then plugging it back in. However, there are a few common causes that may be causing the issue. These include 

• Faulty lid switch
• Faulty shift actuator
• Damaged water inlet valve
• Low water pressure
• Faulty control board
• Faulty motor
• Jammed load

Now let’s talk about the solutions one by one below:

How To Fix Maytag Washer Stuck on Sensing?

1. The faulty lid switch

When your Maytag washer is stuck on sensing, the lid lock is the first thing to examine. A broken lid lock generally stops the washer from closing, and if it does, the washer struggles to start. In short, the washer will most certainly remain in sensing mode.

If you have a whirlpool washer that is stuck on sensing, find the fixes here.

How to fix it:

Set your Maytag washer to diagnostic mode to see if the lid lock is the issue. You should replace the lid lock once the self-test (diagnostic) confirms that it is malfunctioning. Remember that you can use a multimeter to test the lid lock. If there is no continuity, it is defective, and you should replace it.

2. The faulty Shift Actuator

The shift actuator is required to toggle between the spin and washing cycles. If this component fails, your washer will not switch between cycles and will you get the Maytag washer stuck on sensing error.

How to Fix it:

Set your Maytag washer in diagnostic mode to identify the issue code before concluding the shift actuator is malfunctioning. If the diagnostic results confirm this, you should replace the shift actuator. Remove the belt guard to replace it. This will give you access to the faulty shift actuator. You’ll need to unscrew it and then screw in the replacement.

3. Defective water inlet valve 

The water inlet valve connects the cold and hot water hoses. Unfortunately, it can break down and stop controlling water flow into your Maytag . This valve breaks because of two reasons: it clogs or it wears out. The valve may become clogged with dirt and cease to function, or it may wear out over time.

How to Fix it: 

If you suspect a faulty inlet valve, consider using a digital multimeter to test it. If there is no continuity, it is faulty and should be replaced. It stops responding to the washer’s commands due to wiring and electrical faults and may occasionally cause the Maytag washer stuck on sensing error.

4. Low water pressure

It is possible that your washer is not going past the sensing mode owing to low water pressure rather than a malfunction. So, in addition to focusing on Maytag Centennial washer sensor difficulties, you should check your water pressure.

How to fix it:

Using a home water pressure tester, check the pressure in your washer. The washer requires at least 20 psi to work. Adjust the pressure from the main if it is too low. It may also aid in the removal of any kinks in the drain pipe or anything else that may be reducing your home’s water pressure.

5. Faulty control board

An electrical surge can sometimes burn the capacitors on the control board. If the capacitor is burned, your washer will not move past sensing mode. The control board houses a variety of washer-related components. As a result, if the control board fails, your washer will not perform properly or may begin to malfunction.

How to fix it:

A multimeter will be required to solve this problem. Use it to determine whether or not the control board has a defect. If it does, please consider replacing your washer’s control board.

6. Faulty motor

The motor is another component to consider if your washer becomes stuck on sensing. It’s possible that your motor is being clogged, preventing it from rotating the tub. In this case, the sensing light will flash continuously, but it will not proceed past the sensing mode and you will keep getting the Maytag washer stuck on sensing error.

How to Fix it:

In order to resolve this issue, inspect the motor and attempt to remove any material that is blocking and preventing it from turning. After removing the object that caused the blockage, restart the washing machine and it will resume normal operation.

7. Jammed Load

If you overload your Maytag washer with laundry or if the laundry is out of balance, it may remain in sensing mode. So, before running any diagnostics or thinking of replacements, verify the load.

How to Fix it:

Reduce the load if it is too heavy for the washer. Ideally, you should not fill your washer more than 75 percent of its capacity. However, if the laundry load is not excessive, check to see if it is correctly balanced within the washer. If it isn’t, rebalance it before spinning the washer.

Conclusion

So those were some of the quick ways to fix the Maytag washer stuck on sensing problem. The above methods will help you troubleshoot the issue. If they fail to do so, then resetting your Maytag washer would come in handy.

Now go ahead and try the fixes out by yourself and see if they are of any use to you. Also, for any other questions, do comment below.

Also Check:

• Amana Washer Stuck On Sensing Fill
• Air Conditioner Sounds Like A Jet Engine
• Vivint Thermostat Not Working